Hoppecke Hoppecke Battery Battery SB12-80 SB12-80 genuine offer Description: Hoppecke (HOPPECKE) OPZV series VRLA sealed batteries Features 1. Poles and sealing systems 1.1 uses a threaded brass pole, can withstand more than 30I10 current discharge. 1.2 pole using arc welding, labyrinth design, multi-mode epoxy sealed, never without leakage occur. 1.3 pole Column labyrinth (also known as sliding) sealed battery can ease the late growth plate (the extension) to the pole of pressure to ensure good sealing performance during the entire life battery. 1.4 battery can be used for horizontal installation (also called horizontal installation), usually easy to detect the battery electrical performance, easy to connect and easy to replace if it fails. 1.5 Connection with copper or plastic coated copper wire that can withstand the impact of high current discharge, plastic bolt cover, ensure the installed battery terminals, connectors are not in contact with air, no oxidation in fear. 2. positive and negative plates 2.1 positive Multiple board with lead calcium tin alloy tubular plate, and a sheath protecting, high corrosion resistance. Negative plate for lead-calcium-tin alloy multi-gate type plate. 2.2 self-discharge. Average monthly self-discharge rate of 2%, after storage for two years under 20 ℃, there are more than 50% of the capacity, ie without additional power within two years. 2.3 Anti-deep discharge capacity after discharge may continue to receive 100% of the load , the charge restore the original capacity within four weeks. 2.4 internal resistance, 0.268mΩ. 2.5 special additives to prevent the molten alloy calcium calcium loss. 3. The proof of the safety valve 3.1 battery with automatic open and close valve function; valve opening pressure 18Kpa, closing valve pressure 8Kpa, reliable open and close> 45000 times with a fire retardant 3.2 valve parts, anti-acid. and the temperature coefficient. 3.3 in case of fire when charging or overcharging, internal will not detonate. 4. 4.1 HOPPECKE OPZV electrolyte battery using a solid gel electrolyte, in the same volume, electrolyte capacity greater than the general maintenance-free battery (adsorption) 20% ~ 30%, heat capacity, heat dissipation capability, to avoid the general battery is easy to produce thermal runaway phenomenon. 4.2 As the gelled solid electrolyte, so that a uniform concentration of the electrolyte, the acid stratification does not exist. 4.3 acid concentration is low, weak plate corrosion, making extremely long battery life expectancy. Use float up to 20 years. 5. Battery gas recombination rate of 5.1 battery gas recombination rate of 99.99%. 6. Shell 6.1 HOPPECKE OPZV 2V series shell material: SAN, 12V series PP. 6.2 high mechanical strength to withstand a long time batteries, external differential pressure and external impact. 6.3 Anti-oxygen permeability, excellent anti-loss performance, prevent anodic oxidation and electrolyte loss. 6.4 shell casing and sealed with high temperature heat sealing cap sealing technology to effectively prevent leakage, the lower part of the shell integration. 6.5 2V battery with columnar design, good heat dissipation. 6.6 battery in the environment - within the range of 30 ℃ ~ 40 ℃, can withstand 50Kpa positive or negative, continuous 3 ~ 5S, housing will not break, no distortion, no spills, no case after pressure release residual deformation. 7. 7.1 HOPPECKE OPZV capacity battery rated capacity logo is at ambient temperature 20 ℃, the termination voltage 1.80V / monomer, 10h rate capacity. 7.2 HOPPECKE OPZV battery rated capacity (AH): 2V series 200,250,3 00,350,420,490,600,800,1000 1200,1500,2000,2500,3000 6V Series 2 00,250,300 12V 50,100,150 Series 8. Connect the battery connection drop for drop 8.1 5mv. 9. 9.1 life cycle life of the battery 100% depth of discharge> 800 80% depth of discharge> 50% depth of discharge 1200> 2500 20% depth of discharge> 5000 9.2 battery float life of the ambient temperature 20 ℃ 20 years . Hoppecke Battery - Hoppecke Germany (Germany BRILON), as a professional battery manufacturing company, Hoppecke battery (original German pine battery) batteries and related accessories have been produced up to 80 years. We offer thousands of worldwide battery types and products with patented technology to meet customer demand. German Hoppecke batteries SB series VRLA batteries 1. electrolyte absorption in the glass fiber = reduced maintenance (no need to add water) = horizontally (optional) 2. tempering protection devices and integrated in the battery cover central exhaust system eliminating the risk of explosion = 3. Smooth battery lid with a handle for easy cleaning of the surface = = easy carrying 4. Integrated terminal system connector = corrosion resistance even when installed = short circuit is prevented from occurring 5 Service life more than 12 years (according to EUROBAT) German Hoppecke batteries SB series VRLA batteries 1. electrolyte absorption in the glass fiber = reduced maintenance (no need to add water) = horizontally (optional) 2. Press fire protection devices and a central exhaust system integrated in the battery cover = exempt explosion hazard 3. Smooth battery lid with a handle = Easy to clean surface = easy to cultivate 4. Integrated terminal system connector = = corrosion even in When the installation is also possible to prevent the occurrence of a short circuit 5. The life of more than 12 years (based on EUROBAT) Advantages: electrolyte adsorption reduced maintenance (no added water) horizontally (optional) tempering protection devices and integrated in the fiber in the battery cover the central exhaust system eliminating the risk of explosion maximum energy density small cell size requirements smoothing battery lid with a handle for easy cleaning of the surface easily carrying integrated terminal / system connector corrosion resistance even when the installation is also possible to prevent a short circuit The occurrence of major applications. Hoppecke Battery Products 1, good Hoppecke battery safety performance: No electrolyte leakage under normal use, no cell expansion and rupture. Good battery discharge performance: stable discharge voltage, discharge platform gently. 2, the battery good resistance to shock: fully charged battery completely fixed to 4mm amplitude, frequency vibration 16.7HZ one hour, no leakage, no cell expansion and cracking, open circuit voltage is normal. 4, good impact resistance: the battery is fully charged state 20CM height from the natural fall to 1CM thick hardwood board 3 times no leakage, no cell expansion and cracking, open circuit voltage is normal. 5, resistance to over-discharge: 25 degrees Celsius, the battery is fully charged state of constant resistance discharge 3 weeks (only the equivalent resistance of the battery discharge requirements 1CA resistance) to restore the capacity of more than 75% in 6, good resistance to charge: 25 degrees Celsius, fully charged battery 0.1CA charge for 48 hours, no leakage, no cell expansion and cracking, open circuit voltage is normal, the capacity retention rate of 95% to 7, and good resistance to high current: fully charged battery 2CA discharge 5 minutes or 10CA discharge for 5 seconds. No conductive part of the fuse, without the appearance of deformation. 8, high compression glass wool pipette type (AGM) technology. 9, containing explosive devices, the use of ultrasonic welding technology to enhance battery tightness. 10, senior lead - tin - calcium - silver alloy anode, a strong high-current discharge after backfilling and anti-erosion ability. Design - pole and sealing systems: HOPPECKE battery with a special coating, labyrinth pole, high anti-corrosion. - Ex-valve; - positive and negative plates: HOPPECKE positive plate, effectively preventing the active material shedding, extend battery life, to ensure that the number of cycles 700-800 times. - Partition plate; - electrolyte; - housing and sealing systems: battery case should be reinforced polypropylene, and meet the following requirements: resistance to high water loss performance, prevent battery electrolyte loss; anti-oxygen permeability, prevent anodizing; high mechanical strength to withstand a long time batteries, external differential pressure and impact force during transport. Poles and sealing system uses a threaded brass pole, can withstand high current (including battery short-circuit current) through, when the 30I10 discharge 3min, the pole should not be blown, its appearance should not be an exception. Pole using arc welding methods, and fully guarantee a good seal around the base of the pole, causing the pole to avoid the Mifengbuyan leakage occurs after the operation. Battery positive and negative terminals for easy connection, and there are clear signs. Battery terminals should be used bolts, nuts, connecting the voltage drop between the battery △ U≤10mV. Ex-valve opening pressure relief valve HOPPECKE battery within the range of 11 kPa ~ 18 kPa, closing valve pressure should be within the range of 5.6 kPa ~ 8.7 kPa, the reliability is not less than 50 000 times. Exhaust valve action is more sensitive. Positive and negative plates positive and negative plates made of lead-calcium-tin multi-alloy, and has the following characteristics: can withstand high rate charging; strong recovery after · deep discharge, 80% DOD charge and discharge cycles of not less than 700 cycles; · hydrogen evolution voltage should not be less than 2.40V, less water loss, with better maintenance; · There is good hardness and strength; · have effective measures to prevent the loss of calcium in molten calcium alloy; ? plate curing well, not appear from powder, off the block, surface cracks phenomenon; · effectively control the content of iron, manganese, arsenic, chlorine, copper and other impurities, to avoid increasing the amount of oxygen precipitation cells, resulting in increased self-discharge. Battery check and maintenance instructions: a case of corrosion of a monthly content inspection, visual inspection of the battery whether the appearance of severe deformation connecting strip focused on checking the site of three of the most prone to leakage pole, valves, closures. 2, measuring the battery float voltage, float current. 3, the ambient temperature measurement of the battery pack should be kept at 25 ℃ for 20 ℃. 4, pay special attention to single-voltage ahead or behind the battery. Second, the contents of a quarterly review, the terminal voltage of each single cell parameters such as voltage deviation value is greater than the need for manufacturers to provide both charge. 2, the temperature of the surface of each single cell battery pay attention to whether there is overheating. Third, examine the contents of a year, check the connection screw tightening torques and connection status. 2, ventilation battery compartment 3, do a depth of 30-40 check the discharge test. Six float voltage impact float voltage has a direct impact on the battery life. Float voltage higher than the recommended limit will reduce battery life. Below the recommended float voltage can lead to insufficient battery capacity. The following table shows the temperature compensated float charge after 6 without pressure on the battery life. Hoppecke (HOPPECKE) OPZV series VRLA sealed batteries Features 1. Poles and sealing systems 1.1 uses a threaded brass pole, can withstand more than 30I10 current discharge. 1.2 pole using arc welding, labyrinth design, multi-mode epoxy sealed, never without leakage occur. 1.3 pole Column labyrinth (also known as sliding) sealed battery can ease the late growth plate (the extension) to the pole of pressure to ensure good sealing performance during the entire life battery. 1.4 battery can be used for horizontal installation (also called horizontal installation), usually easy to detect the battery electrical performance, easy to connect and easy to replace if it fails. 1.5 Connection with copper or plastic coated copper wire that can withstand the impact of high current discharge, plastic bolt cover, ensure the installed battery terminals, connectors are not in contact with air, no oxidation in fear. 2. positive and negative plates 2.1 positive Multiple board with lead calcium tin alloy tubular plate, and a sheath protecting, high corrosion resistance. Negative plate for lead-calcium-tin alloy multi-gate type plate. 2.2 self-discharge. Average monthly self-discharge rate of 2%, after storage for two years under 20 ℃, there are more than 50% of the capacity, ie without additional power within two years. 2.3 Anti-deep discharge capacity after discharge may continue to receive 100% of the load , the charge restore the original capacity within four weeks. 2.4 internal resistance, 0.268mΩ. 2.5 special additives to prevent the molten alloy calcium calcium loss. 3. The proof of the safety valve 3.1 battery with automatic open and close valve function; valve opening pressure 18Kpa, closing valve pressure 8Kpa, reliable open and close> 45000 times with a fire retardant 3.2 valve parts, anti-acid. and the temperature coefficient. 3.3 in case of fire when charging or overcharging, internal will not detonate. 4. 4.1 HOPPECKE OPZV electrolyte battery using a solid gel electrolyte, in the same volume, electrolyte capacity greater than the general maintenance-free battery (adsorption) 20% ~ 30%, heat capacity, heat dissipation capability, to avoid the general battery is easy to produce thermal runaway phenomenon. Deli Technology Co., Ltd. Beijing Branch of the product if you need detailed technical specifications, parameters, quotes. Please call 24 hours Sales Tel: 010-56122689 The company sells the following products: 1: Germany sunshine battery 3: Hercules batteries 2: San Yang Battery 4: Hills Battery 5: BB Battery 6: Champion Battery 7: 8 Yuasa Battery : Union Battery 9: Matsushita Battery 10: 11 Hills of UPS Emerson UPS power 12: APCUPS Power 13: 14. Branch Kstar batteries battery battery 15. Hirt (import colloid) 16. Dorset battery 17: Pirate Battery